D Deyou Home Decor

How to Order Wholesale from Deyou: From Enquiry to Order

This page sets out the wholesale ordering process at Deyou Home Decor in the order a distributor buyer follows it: shortlist designs from the catalogue, send an enquiry, work out quantities, check samples, and confirm specifications and quantities before placing the order. Deyou Home Decor is a Yiwu-based wholesale supplier of wall and floor coverings for wholesalers, distributors and project customers.

Use this page for the steps. The figures sit on the pages linked from each step; where this page says confirm before ordering, the detail is unpublished or varies by design, so confirm it for your order rather than assuming it.

Start with the catalogue

The catalogue holds 88 products in 8 categories: 3D Gel Peel and Stick Wall Tiles, Aluminum-PVC Peel and Stick Wall Tiles, Decorative Fluted Wall Panels, Peel and Stick Floor Tiles, Waterproofing Membranes, UV Decorative Wall Panels, Sticker Tiles and 3D Acoustic Panels. Open the product page for each design under consideration and note the model code together with the size, thickness, coverage and packing shown for that exact design.

Check the published size, thickness, coverage and packing figures in our sizes, thickness, coverage and carton packing quick reference before enquiring, and keep any figure that is not published on a list to confirm. Do not borrow a figure from another design, even one of the same size: coverage and packing vary by design.

Send the enquiry through the contact page or WhatsApp

Send the enquiry through our contact page, which asks for your name, phone number, email address, company name and message, or by WhatsApp on +86 18058983135.

Give the destination country, the designs you are interested in with their model codes, the installation surface, and the estimated quantity for each design. Ask for the catalogue and a wholesale quotation, and include your email address in the enquiry.

A complete first enquiry lets the designs, quantities and specifications be checked together. Keep the model codes and quantities in the message itself, so the enquiry can be checked without a second round of questions about which designs it covers.

Work out quantities and check the minimum orders

Work out quantities with the method in our how to measure walls and work out how many tiles to order, which works wall by wall from effective coverage and allows for cutting and spares. Check the calculated quantity for each design against the minimum order for its line: where the calculation falls below the minimum, the minimum governs.

  • Wall tiles (gel and aluminum-PVC): minimum 2,000 pieces per design, with at least 5 designs per order.
  • Acoustic panels: minimum 125 pieces per design per colour, with at least 5 designs.
  • UV panels: minimum 100 sheets per colour.

These are the only minimum orders stated here. For every other line, confirm the minimum order before ordering.

Check samples before placing a full order

Before placing a full order for peel-and-stick backsplash tiles, build a small test panel from samples of the same design. The panel shows how the seams, cut edges and finish look once the pieces are installed together.

Check the panel in three ways: join pieces and inspect the seams under side lighting for gaps, changes in relief and differences in gloss; make a trial cut with the recommended cutting tool and inspect the edge for tearing or lifting beside a corner or trim; and test the sample on the intended wall surface, prepared as the installation instructions direct, inspecting the corners for lifting.

Ask the supplier to confirm any restrictions near heat sources or in damp areas before ordering, and confirm the usable coverage of gel tiles against the sample rather than calculating from the nominal sheet area. The samples guide states none of the sample cost, courier arrangements or refundability: confirm all three before ordering.

If no catalogue product fits: OEM customization

Deyou offers OEM and ODM services for importers, distributors and home decor brands. Our OEM page lists five areas that can be customized:

  • Product size and thickness
  • Colors, patterns and surface finishes
  • Materials: UV panels, PVC, polyester fiber and 3D panels
  • Packaging and labeling
  • Customer branding and logo

To start, send your requirements through the contact form, giving the product, size, color and approximate quantity you need; the team replies with a proposal and the next steps. The form on the OEM page also accepts attachments (JPG, PNG, DOC, DOCX, PDF, XLSX and XLS files, maximum 10MB per file).

For the choice between the OEM route and the ODM route, see our OEM vs ODM guide.

Confirm specifications and quantities before ordering

Before ordering, confirm each of the following for the exact designs in the order. Do not substitute a figure from another design:

  • Size, thickness, usable coverage and carton packing for each design, including any figure the product page leaves open.
  • Quantity for each design and the number of designs, checked against the minimum order for the line.
  • Packing for the order, including any packing detail the product page leaves open.
  • For fluted panels, every specification: size, thickness, base material, fixing method, packing and minimum order.
  • For UV panels, the thickness for each design, where thickness is listed as an option.

Anything on this list that stays open after the enquiry stays open until it is confirmed: confirm it before ordering rather than assuming it from another design or another line.

Place the order with the confirmed details

Send the confirmed order through our contact page or by WhatsApp, giving the designs with their model codes, the confirmed specifications, the quantities for each design, and the packing agreed for the order.

Keep the confirmed details together in a single message, so the order can be checked design by design against the enquiry, the sample checks and the confirmed specifications.