义 义乌德佑进出口有限公司

Cleaning Peel and Stick Wall Tiles: The Factory Method and What to Confirm

After the sale, distributors hear the same question from shop owners and end customers: how do I clean these tiles? The answer depends on the product line, and this guide answers it for two lines only — Deyou's 1 mm gel tiles and 3 mm aluminum-PVC tiles, both made by the same manufacturer. The factory's cleaning guidance is short: a neutral cleaner, wiped with an ordinary cloth. This article explains how to use that method, room by room, and marks clearly where the factory's answer ends and a question must be confirmed before ordering.

The factory method: a neutral cleaner and an ordinary cloth

The guidance comes from the manufacturer, not from a general cleaning blog. Asked how the tiles should be cleaned, the manufacturer answered: neutral cleaner, ordinary cloth wipe. "Neutral" means a cleaner labelled neutral or pH-neutral — neither strongly acidic nor strongly alkaline. "Ordinary cloth" means a regular household cloth, with no special tool required. That is the whole method, and it applies to the gel and aluminum-PVC lines the factory makes. The factory gave no list of banned products, so this guide states none: where a customer asks about a specific cleaner, the answer is to check the product's own instructions and confirm with the supplier before using it.

A routine wipe, step by step

For everyday cleaning, the method is a wipe, not a wash. Dampen an ordinary cloth with a neutral cleaner and wipe the tile face, working across the wall section by section. Follow with a pass of a clean, damp cloth so no cleaner film stays on the surface, then let the wall air-dry. For dust between cleaner wipes, a dry ordinary cloth is enough. When a new cleaner is used for the first time, try it on one inconspicuous tile first and check the finish before cleaning the whole wall. The point of the routine is regularity: light, frequent wiping keeps the face clean without ever needing a heavy clean.

Kitchen backsplashes: grease and everyday splashes

Both lines suit kitchen backsplashes, where the daily enemies are grease and water splashes. Wipe splashes soon after cooking, before grease builds into a film — the same neutral cleaner and ordinary cloth, used often, is the whole routine. The gel tiles' surface helps here: the waterproof guide notes that water sits on the 1 mm gel surface and wipes off, with no grout to stain and nothing to seal. Cleaning is a separate question from heat: how close tiles may sit to a stove is covered in the stove-safety guide, not here.

Bathroom walls: water, steam and soap marks

Bathroom walls collect water splashes, steam and soap marks, and the same wipe applies: neutral cleaner on an ordinary cloth, then a pass with a clean damp cloth. Wipe water off the tile face rather than leaving it to stand. One boundary matters: this guide covers bathroom walls, not shower interiors or other direct-water locations. The gel tile category page asks buyers to confirm wet-area suitability before specifying the tiles for showers or direct-water locations, and the aluminum-PVC page asks the same — confirm before ordering where a location takes direct water.

Gel and aluminum-PVC: the same method, different faces

The two lines share one cleaning method but have different faces. Gel tiles are 1 mm thick (1.0 ± 0.05 mm): a PU or epoxy gel surface on a PET base with a self-adhesive backing, with a glossy, raised tile effect — YJC0224, for example, is 294 × 214 mm per sheet. Aluminum-PVC tiles are 3 mm composite sheets: a metal-look aluminum surface on a PVC core, with a real metallic finish — YLS002 is 306 × 298 mm, with an effective coverage of about 306 × 291 mm. Confirm the exact finish of the selected design with a physical sample. The material comparison sets the two lines side by side; browse the gel range and the aluminum-PVC range for the full pattern lists.

Joints, edges and the protective film

Wipe along the tile face, including the visible joints between sheets. On gel sheets, overlap only where the sheet is marked "Overlap here" — the joints are part of the pattern, and the wipe follows the face rather than working under it. The front protective film on gel tiles is removed during installation; it is not a cleaning layer, and a tile that still has its film on is not finished. If an edge lifts, that is an installation matter, not a cleaning one: the installation guide covers wall preparation and application, and a lifting edge should be checked against those steps rather than pressed back during cleaning.

What this guide does not cover

This method covers the gel and aluminum-PVC lines only. Cleaning guidance for the other lines Deyou sells — UV panels, acoustic panels, fluted panels, wall rolls, floor tiles and waterproofing membranes — is not confirmed, and this method must not be extended to them: confirm the cleaning method for those lines before ordering. The factory gave no list of banned cleaners or tools, and this article invents none. Public guidance from other brands disagrees with itself — Aspect's stone-tile FAQ bans vinegar, while WOTILE recommends a 50/50 white-vinegar-and-water mix for kitchen grease, both observed in November 2026 — which is why the only cleaning guidance used here is the factory's own method and the product's own instructions. For anything beyond routine wiping, such as set-in stains or cleaning equipment, confirm with the supplier before proceeding.

How to enquire

Send the model or pattern, the colour, the quantity per design and colour, and the destination through the contact form, and describe the room and the cleaning question so the right product instructions can be checked. Request a physical sample first, and test the cleaning method on the sample before ordering. Deyou's products have passed independent third-party testing. Browse the gel range and the aluminum-PVC range first, so the enquiry can name the closest existing products.