义 义乌德佑进出口有限公司

Peel-and-Stick Floor Tiles: A Buyer's Guide to the 6 Models

This guide covers the 6 peel-and-stick floor tiles in our floor tiles category (IDs 69–74). All 6 share the same published format, so the buying decision turns on design, the room and the substrate, and the items that still need confirmation — not on choosing between sizes.

Use this guide with the sizes, thickness, coverage and carton packing quick reference, which lists the published figures for the full range. Every figure in this guide comes from the product pages; where a figure is not published, the guide says so and marks it for confirmation.

The 6 models at a glance

Every model below is a 300 × 300 mm square tile, 1.5 mm thick, with a 5-layer structure that includes a wear layer. The nominal area is 0.09 m² per tile: stated on the pages for DY-FT001, DY-F001-FTS159 and FTS195, and the same arithmetic from the stated size for FTS023, FTS027 and FTS050.

Model Design Size Thickness Structure
DY-FT001 Black and white checkerboard 300 × 300 mm 1.5 mm 5 layers, including a wear layer
DY-F001-FTS159 Light wood-grain herringbone 300 × 300 mm 1.5 mm 5 layers, including a wear layer
FTS195 White marble effect 300 × 300 mm 1.5 mm 5 layers, including a wear layer
FTS023 Blue ornamental 300 × 300 mm 1.5 mm 5 layers, including a wear layer
FTS027 Pink geometric 300 × 300 mm 1.5 mm 5 layers, including a wear layer
FTS050 Vintage floral medallion 300 × 300 mm 1.5 mm 5 layers, including a wear layer

The 5 layers, as listed on the pages, are a UV protective layer, a wear layer, a printed decorative layer, a stone-plastic base and an adhesive layer. The pages for FTS023, FTS027 and FTS050 describe the first two as a scratch-resistant UV layer and a wear-resistant layer; the layer count and order are the same.

Why the wear layer matters: floor tiles are not wall tiles

The factory states that the gel and aluminum-PVC wall tiles must not be applied to floors, because their surface has no wear layer. This is a factory statement about those wall tiles; it says nothing about other lines, and its scope beyond the gel and aluminum-PVC wall tiles is not stated.

The floor tiles differ on exactly this point: each of the 6 lists a wear layer within its 5-layer structure. That is the structural difference to check first when a buyer asks whether a wall design can be used on a floor — for the gel and aluminum-PVC wall tiles, the factory answer is no. Our wall tiles vs. floor tiles guide sets out the wider comparison; this guide stays with the floor tiles.

A listed wear layer is not a wear rating. No page for the 6 models states a wear rating or a technical performance figure: the pages for DY-FT001, DY-F001-FTS159 and FTS195 state that wear rating and technical performance are to be confirmed with documentation for the supplied model, and the pages for FTS023, FTS027 and FTS050 state that specific durability or performance ratings require factory confirmation or verification. Confirm the rating for the exact model before ordering.

Rooms: only what the pages state

The room wording differs between the two page groups, so read the wording for the exact model. The pages for DY-FT001, DY-F001-FTS159 and FTS195 say to consider the tiles for dry interior residential renovation and decorative floor projects. They add that commercial use must be assessed against traffic, wear, slip and maintenance requirements, and that no commercial-use classification is confirmed on those pages.

The pages for FTS023, FTS027 and FTS050 list recommended applications: residential living rooms, bedrooms, indoor hallways, entryways and dry interior decorative areas, plus suitable light commercial interiors. That light-commercial wording appears only on those 3 pages; do not carry it across to the other 3 models.

All 6 pages exclude the same wet locations. The pages for DY-FT001, DY-F001-FTS159 and FTS195 state that the tiles must not be specified for shower floors or standing-water locations. The pages for FTS023, FTS027 and FTS050 state that shower areas and waterlogged floors are excluded or not recommended. No page names kitchens or bathrooms as suitable rooms, so suitability for a kitchen or bathroom floor is not established by the pages — confirm it for the intended room before ordering. The pages for DY-FT001, DY-F001-FTS159 and FTS195 add that surface resistance does not establish waterproof joints or a waterproof flooring system.

Substrate and installation: what the pages state

Installation on all 6 pages is peel and stick on a compatible prepared substrate, with a self-adhesive backing. The pages for FTS023, FTS027 and FTS050 add that the tiles generally do not require additional conventional flooring glue on properly prepared surfaces, and that the product catalog lists stone tiles and wooden floors among suitable substrates.

The installation steps stated on the pages are: confirm the existing floor is dry, flat, clean, sound and compatible with the adhesive, treating uneven joints and surface defects first; measure the area and dry-lay the pattern, allowing for cuts at walls and obstacles; peel the backing, align the tile and press evenly, including the edges; and trim perimeter pieces with suitable tools, following the supplier instructions for finishing and use after installation.

Some details appear on one group only. The pages for DY-FT001, DY-F001-FTS159 and FTS195 add a test of adhesion on a small area of the actual substrate. The pages for FTS023, FTS027 and FTS050 start installation from a corner of the longest wall, and the page for FTS023 adds placing tiles closely without forcing the edges together.

All 6 pages exclude the same substrates: do not apply directly to rough concrete or uneven or oily surfaces. Wet locations are excluded as set out above. The pages for DY-FT001, DY-F001-FTS159 and FTS195 add that visible grout lines or unevenness require preparation before the tiles can cover existing tiles, and that substrate preparation must be confirmed before installation.

Working out quantities

The pages for DY-FT001, DY-F001-FTS159 and FTS195 give the method directly: divide the area in square metres by 0.09 and round up, then add an allowance for cuts and pattern matching according to the layout. The same 0.09 m² nominal area follows from the stated 300 × 300 mm size for FTS023, FTS027 and FTS050, so the same division applies to all 6 models.

For example, a floor of 10 m² needs 10 / 0.09 = 111.11 tiles before rounding, so 112 tiles before any allowance for cuts and pattern matching. Work the allowance from the layout — cuts at walls and obstacles, and pattern alignment across adjacent tiles — rather than from a fixed figure, since no page states one.

Pattern matching deserves its own check for the patterned designs. The checkerboard design continues across adjacent tiles, and the herringbone design needs its direction and alignment planned across adjacent tiles before the backing is peeled — both points are stated on the DY-FT001 and DY-F001-FTS159 pages. Dry-lay the pattern before fixing, as the installation steps require.

Care, and what to confirm before ordering

The care wording on the pages is brief. The pages for DY-FT001, DY-F001-FTS159 and FTS195 state that buyers should follow the supplied cleaning instructions, use non-abrasive tools and avoid soaking the floor. The pages for FTS027 and FTS050 state that the surface should be cleaned with a soft cloth or suitable non-abrasive cleaning tools, avoiding prolonged standing water, sharp objects and harsh cleaning chemicals. The page for FTS023 states only that the surface can be maintained with a slightly damp, soft cloth. No page states a cleaning agent, and no page states a lifespan — do not borrow the cleaning or lifespan statements published for the gel and aluminum-PVC wall tiles, which cover those wall tiles only.

Confirm the following before ordering, for the exact model:

  • Wear rating and technical performance, with documentation for the supplied model.
  • Room suitability for the intended room, including kitchens and bathrooms; commercial use, assessed against traffic, wear, slip and maintenance requirements.
  • Packing and carton data — no page for the 6 models states carton contents, carton size or weight.
  • Minimum order quantity and lead time — the pages state that these are to be confirmed in the quotation.
  • Lifespan, and the full cleaning instructions supplied with the tiles.

How to enquire

Send the enquiry through our contact page with the model code, the quantity or floor area, the destination country and port, and any sample or packing requirements — the items the DY-FT001, DY-F001-FTS159 and FTS195 pages ask for. Browse the 6 designs on the floor tiles category page and check the figures against the product pages before ordering.