义 义乌德佑进出口有限公司

How to Measure Walls and Work Out How Many Tiles to Order

Ordering the right quantity starts with a clear record of the walls to be covered and the exact design to be used. This page sets out the working method in order — record, convert, allow for cutting, and check the result — so the quantity can be confirmed with the supplier before ordering.

Two companion pages carry the figures: our quantity guide, which answers the question in brief, and the sizes, thickness, coverage and carton packing quick reference, which lists the published size and coverage figures for all 88 products. Use this page for the method, those pages for the figures; where a figure is not published, confirm it rather than guessing.

Work wall by wall

Treat every wall as its own calculation. For each wall, record the height and the width, and multiply the two to get the area of that wall. Keep one row per wall, and add the separate wall areas together only at the end. A single combined measurement hides mistakes; a wall-by-wall record lets each figure be checked on its own.

On the same record, note everything that interrupts the surface — sockets, switches, edges, corners and openings such as doors and windows — with the position of each one. These notes show where cuts will be needed and let the quantity be worked out from the layout instead of a bare total. Keep opening measurements apart from wall measurements, so the layout decides how they are treated.

Turn wall area into a sheet quantity

A quantity worked out from sheet size can come up short: a sheet covers no more wall than its own size once the edges of the pattern meet. Work from effective coverage instead — the wall area one sheet actually covers — taken from our sizes, thickness, coverage and carton packing quick reference, which lists the published coverage figures design by design. Never borrow the coverage of another design, even one of the same sheet size: coverage varies by design.

The conversion itself is one division: wall area / effective coverage per sheet = sheets needed. Round the result up to a whole number of sheets — part sheets cannot be ordered.

For model YLS002, the published dimensions give: sheet 306 × 298 mm, effective coverage about 306 × 291 mm, so 0.306 × 0.291 = 0.089 m² per sheet. Use that per-sheet figure in the formula above.

Gel tiles need a different first step: no gel product page states a usable coverage, and the pages say to confirm usable coverage with the sample, so do not calculate a gel quantity from the nominal sheet area. Confirm the usable coverage first, then apply the same division. The same applies to rolls and panels: use the usable coverage of the exact design, confirmed where unpublished.

Cutting waste and spares

The divided result is a starting point, not an order quantity. Cutting takes material the division does not count: cuts around sockets and switches, cuts at edges and corners, and cuts made to line a pattern up across neighbouring sheets. Offcuts count only where they fit a remaining section. Keep spare sheets aside for repairs after installation, so a damaged sheet can be replaced from the same order.

The size of the allowance depends on the layout: the number of cuts, the number of sockets and openings, and how much pattern lining-up the design requires. No fixed allowance applies here — agree it for the order once the measurements and the design are known. Our installation guide shows how cuts beside sockets and edges are marked and made.

Check the quantity against the minimum order

The order quantity for a design is the larger of two figures: the calculated quantity, including the agreed cutting allowance and spares, and the minimum order for that line. Below the minimum, the minimum governs; above it, the calculation governs.

  • Wall tiles: 2,000 sheets per design, with at least 5 designs.
  • Acoustic panels: 125 panels per design and colour, with at least 5 designs.
  • UV panels: 100 sheets per colour.

These are the only minimum orders stated here. For other lines, confirm the minimum order before ordering.

What to confirm before ordering

The following are unpublished or need confirmation. Confirm each one that affects your order, and do not substitute a figure from another design:

  • Usable coverage for all gel tiles and for aluminum-PVC model mt-xgt-02 (ID 36) — check it against the sample, not against sheet size.
  • Fluted panels: size, thickness, base material, fixing method, packing and minimum order — all of it.
  • Carton data for aluminum-PVC models YLS002 (ID 23) and YLS234-QH (ID 31), for gel IDs 100–109, and for acoustic ID 75.
  • Roll weight basis for the six EPE marble rolls (IDs 93–98): whether the reference 25 kg is net or gross, and the final confirmed weight.

How to enquire

Send the enquiry through our contact page with the wall-by-wall record, the designs and model codes, the quantity worked out above, and the checklist items that need confirming. The record itself lets the quantity be checked against the layout instead of a single total. For a size or finish that is not listed, our OEM page explains what can be customised.